- Home
- ยป
- Our Products
- »
- DC & AC Energy Meter
DC & AC Energy Meter
435-II Power Quality and Analyzer
Product Brochure
Phase | Three Phase |
Maximum Input Voltage | 1000 Vrms |
Nominal Voltage Range | Selectable 1 V to 1000 V |
Bandwidth | Greater Than 10 kHz, up to 100 kHz for transient mode |
Scaling | 11, 101, 1001, 1,0001 10,0001 and variable |
The new 430 Series II Power Quality and Energy Analyzers offer the best in power quality analysis and introduce, for the first time ever, the ability to monetarily quantify energy losses. The new Fluke 434, 435 and 437 Series II models help locate, predict, prevent, and troubleshoot power quality problems in threephase and single-phase power distribution systems. Additionally, the Fluke-patented energy loss algorithm, Unified Measurement, measures and quantifies energy losses due to harmonics and unbalance issues, allowing the user to pinpoint the origin of energy waste within a system.
- Energy loss calculator: Classic active and reactive power measurements, unbalance and harmonic power, are quantified to pinpoint true system energy losses in dollars (other local currencies available).
- Power inverter efficiency: Simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp.
- Power Wave data capture: 435 and 437 Series II analyzers capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics (generator start-ups, UPS switching etc.).
- Waveform capture: 435 and 437 Series II models capture 50/60 cycles (50/60Hz) of each event that is detected in all modes, without set-up.
- Automatic Transient Mode: 435 and 437 Series II analyzers capture 200 kHz waveform data on all phases simultaneously up to 6 kV.
- Fully Class-A compliant: 435 and 437 Series II analyzers conduct tests according to the stringent international IEC 61000-4-30 Class-A standard.
- Mains signaling: 435 and 437 Series II analyzers measure interference from ripple control signals at specific frequencies.
- 400 Hz measurement: 437 Series II analyzer captures power quality measurements for avionic and military power systems.
- Troubleshoot: Analyze the trends using the cursors and zoom tools.
- Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance.
- Measure all three phases and neutral: With included four flexible current probes with enhanced thin flex designed to fit into the tightest places.
- Automatic Trending: Every measurement is always automatically recorded, without any set-up.
- System-Monitor: Ten power quality parameters on one screen according to EN50160 power quality standard.
- Logger function: Configure for any test condition with memory for up to 600 parameters at user defined intervals.
- View graphs and generate reports: With included analysis software.
- Battery life: Up to 8 hours operating time per charge on Li-ion battery pack.
- Wireless data download: Download data to PC wirelessly and capture screens using Fluke Connect App.
Unified power measurement:
Fluke’s patented Unified Power Measurement system (UPM) provides the most comprehensive view of power available, measuring:
- Parameters of Classical Power (Steinmetz 1897) and IEEE 1459-2000 Power
- Detailed Loss Analysis
- Unbalance Analysis
Online UPS LCD Meter
Minimum Order Quantity: 1 Piece
Product Brochure
Frequency | 50 Hz |
Display | Alphanumeric LCD 16 X 1 back-lit |
Auxillary Supply | +/- 9V to 12VDC |
Input AC Volt | 0-5V for 500V fsd |
Package | 48 X 96 mm facia 23mm depth |
Termination | FRC Male connector 14/20 pin |
Integrated LCD Meter for UPS Model 2031C TRMS ADS 2031 is a Microcontroller based Integrated Digital True RMS Meter to measure Multiple parameters. The Meter measures AC Input Volt & Frequency, Output AC Volt, Current & Freq, DC Volt and Current. The Meter accepts normalised Inputs at 5V FSD. The general range available is 500V AC / DC, 100A AC/DC and Line frequency of 50 Hz.
Features:
- Single meter measures Input AC Voltage & Frequency; Output AC Voltage, Current & Frequency, DC Voltage & Current
- True RMS Measurements
- Micro controller based
- Built-in selector switch
- Back Lit Alphanumeric 16 X 1 Display
- 1% FSD Accuracy
- Software calibration
- Built-in digital noise filter to cater to harsh UPS field
- Compact meter
- RS 232 Interface suits with popular UPS MONitoring software
Technical Specifications:
Input Signal | Input AC volt | 0-5V for 500V fsd |
Input Frequency | from AC Volt | |
Output AC Volt | 0-5V for 500V fsd | |
Output AC Amp | 0-5V for 100A fsd | |
Output Frequency | from AC Volt | |
DC Volt | 0-5V for 500V fsd | |
DC Amp + & - | 0-5V for 100A fsd | |
Additional Information:
- Item Code: ads2031
ADS 2233 S4K
Minimum Order Quantity: 1 Piece
Product Brochure
Model Name/Number | ADS 2233 S4K |
Voltage | 20 - 60V DC |
Usage/Application | Industrial |
Current | 75mV / 100A |
Type | Digital |
Country of Origin | Made in India |
Additional Information:
- Production Capacity: 100
- Delivery Time: 3-5 Days
- Packaging Details: Box
2249 DC Energy Meter Clamp Shunt Base
Power Source | Electric |
Accuracy | better than 1% fsd |
Input Signal | DC V 20 - 60V DC,DC A 100A Cable in CT |
Auxiliary Supply | Self powered |
DC Voltage | 20 - 60V DC |
Current Rating | 100A Cable in CT |
No of Channels | 3 - 7 channels |
CT Vent | 20mm dia & 40 mm Dia |
Display | 16 X 2 Alphanumeric back lit LCD Display |
Clamp Type Dc Cts Lcd Display Rs485 Interface Data Logger
- DS 2249 is a Microcontroller based Integrated Digital Meter to measure Multiple parameters on DC power Management applications. The general range available is 48V DC & 100A DC.
- Clamp type DC CTs - 20 mm dia CT Vent - No Additional Shunts
- Multiple channels 4 and is economically priced.
- Measures & Displays DC Volt, DC Current & DC Energy(KWhr) of each channel. And Cumulative Current & Energy(KWhr).
Additional Information:
- Item Code: ADS2249S4K
ADS2231 S4R DC Energy Meter (VP002116)
Minimum Order Quantity: 1 Pieces
Product Brochure
Type | Digital |
Temperature Range | -20 deg -+55 deg C |
Model No | ADS 2231 S4R |
DC Voltage | 20 - 60V DC |
Current Rating | 75mV / 100A |
No of Channels | 4 channels |
Accuracy | better than 0.5 % |
Display | 16 X 2 Alphanumeric back lit LCD Display |
ADS 2231 is a Microcontroller based Integrated Digital Meter to measure Multiple parameters on DC power Management applications. The general range available is 48V DC & 100A DC.
Features:
- Single meter measures Multiple channels
- Standard Shunt Input 100A/75mV DC
- Measures DC Volt & Amp & Energy of each ch.
- Measures Cumulative Current & Energy
- Micro controller based
- Large Alphanumeric back lit LCD Display
- 0.5% FSD Accuracy
- Software calibration
- Records Data with Time stamp
- RS 232 - RS485 Interface for PC communication
- Built-in noise filter for harsh field conditions
- Compact meter.
Additional Information:
- Item Code: ADS2231S4R
DC Energy Meter Ads2248c 1 Channel
Product Brochure
Phase | Three |
Type | Digital |
Power Source | Electric |
DC Input Voltage Range | 75 mV |
Shunt Value | 75 mV |
Power | 200 kW |
1. mV Input for Current measurement
2 0-600 DC voltage measurement
3. backlit 16 character 2 line LCD DISPLAY
4. Password protected reset mode for kWh
5. Last displayed reading stored for kWh
6. Auxillary powered 90-260V AC/DCAds 2014 T Online UPS LCD Meter (VP002105)
Product Brochure
AC Volt | 0-5V for 500V fsd |
AC Amp | 0-5V for 100A fsd |
DC Volt | 0-5V for 500V fsd |
DC Amp | 0-5V for 100A fsd |
Accuracy | better than 1% fsd |
Display | Alphanumeric LCD 16 X 1 back-lit |
Auxillary Supply | 9 V to 12 VDC |
Package | 96 X 96 mm facia ; 23mm depth |
ADS 2014T is a Microcontroller based Integrated Digital Meter to measure Multiple parameters on a UPS. The Meter accepts normalised Inputs at 5V FSD. The general range available is 500V AC / DC, 100A AC/DC and Line frequency of 50 Hz. It''s specially available at a depth of 23 mm
Features
- Single meter measures AC Voltage, Current & Frequency, DC Voltage & Current
- Micro controller based
- Built-in selector switch
- Back Lit Alphanumeric 16 X 1 Display
- 3.5 digit resolution, 4.5 digit Measurement
- 1% FSD Accuracy
- Software calibration
- Refresh rate of 2-3 samples per Second
- Built-in digital noise filter to cater to harsh UPS field
- Compact meter
Additional Information:
- Item Code: ads2014t
ADS 2034 Online UPS LCD Meter
Minimum Order Quantity: 1 Piece
Product Brochure
Back Lit Alphanumeric | 16 X 2 LCD Display |
FSD Accuracy | 1% |
Phase | Three Phase |
LCD Display Size | 16 X 2 mm |
Accuracy | 1% FSD |
Compact Meter | 96mm x 96mm x 20mm |
ADS 2034 is a Microcontroller based Universal Integrated Digital Meter to measure AC Input Volt & Frequency, Output AC Volt, Current & Freq, DC Volt and Current of 3 Phase or 1 phase systems.
- Integrated LCD Meter for UPS Model 2034 TRMS
- Model 2034-31 (3 input 1 output)
- Model 2034-33 (3 input 3 output)
Features:
- Single meter measures 3Phase Input AC Voltage & Frequency; Output AC Voltage, Current & Frequency, DC Voltage & Current
- 4 Fault annunciation on Display
- Micro controller based
- Built-in selector switch
- Back Lit Alphanumeric 16 X 2 LCD Display
- 1% FSD Accuracy
- Software calibration
- Built-in digital noise filter to cater to harsh UPS field
- Compact meter - 96mm X 96mm - 20mm Depth
- Optional RS 232 Output
Additional Information:
- Item Code: ADS2034
AC Energy Meter 3ph 1 Channel & 1ph 1 Channel
Phase | Three |
Wide Voltage Operating Range | 90 to 260 V phase to neutral |
Input Current | Through 5A CT (Used External CT 125A / 5A CLASS 1 ) |
Frequency | 50/60Hz |
Display Type | Digital |
- Auxiliary Power Supply should be derived from measurement input. RN
- Calibration : using front keys.
- Isolated RS 485 (MODBUS-RTU Protocol) with A , B & common.
- Fully User Programmable.
- CT ratio Settable
- RS 485 9600 baud
- Every Menu Settings should be Password Protected.
- Device ID settable)
- Screw type terminals for connecting wires
- Wide voltage operating range 90 to 260V phase to neutral
- Should measure minimum current passed 0.5%